You are here: Home > Armaspec Buffer Weight > H2
Sort By:
Page of 1
Armaspec AR-15 Braided Carbine Buffer Spring - BBS Armaspec AR-15 Sound Mitigation Buffer - Gen 3 Armaspec AR-15 Stealth Recoil Spring
Armaspec AR-15 Braided Carbine Buffer Spring - BBS
MSRP: $24.99
Sale Price: $21.24
JoeBob dun saved you $3.75!
Armaspec AR-15 Sound Mitigation Buffer - Gen 3
MSRP: $59.99
Sale Price: $39.99
JoeBob dun saved you $20.00!
Armaspec AR-15 Stealth Recoil Spring - Gen 3
MSRP: $84.99
Sale Price: $69.99
JoeBob dun saved you $15.00!
The Armaspec Braided Buffer Spring™ - BBS™ provides improved performance, reliability and functionality to your standard mil-spec buffer spring. You will experience a smoother, quieter and more reliable weapon system. The braid is designed with 51 active coils to give tighter tolerances while being compressed and the three strand design allows for the energy from the bolt carrier to be absorbed and dispersed evenly during cycle time. Utilizing this technology gives you more than double the life of a standard mil-spec buffer spring.

*The BBS™ will fit over standard buffer weights, it can be paired with most buffers on the market.

*The BBS™ is for the use with standard carbine length buffer tubes. It is NOT compatible with rifle length, A5 buffer tubes or receiver extensions.
The Gen3 Sound Mitigation Buffer™ SMB™ is a single-stage captured drop-in replacement for your standard buffer and spring. The SMB™ is designed to keep the buffer spring from rubbing against the inner wall of the buffer tube providing smooth, quiet operation.

FEATURES:
  • Single-stage captured drop-in replacement for your standard buffer and spring
  • Reduce felt recoil
  • Keep the buffer spring from rubbing against the inner wall of the buffer tube providing smooth and quiet operation
  • Adjustable spring weight (*Main spring can be trimmed at .25 lbs per coil to reduce tension up to a max of 12 coils)
  • Made in the U.S.A.
  • Lifetime Warranty

SPECIFICATIONS:
  • Actual Weight (Complete System):
  • Carbine: 4.41 oz.
  • H2: 5.81 oz.

Equivalent Weight:
  • Carbine: 3.3 oz.
  • H2: 4.7 oz.

COMPATIBILITY:
  • AR-15


Models:
  • ARM258-C
  • ARM258-H2
The Stealth Recoil Spring™ SRS™ GEN3 is a self-contained multi-stage drop-in replacement for your standard buffer and spring. The SRS™ is designed to keep the buffer spring from rubbing against the inner wall of the buffer tube providing smooth, quiet operation and the second stage helps reduce the felt recoil significantly.

NOTE: The new GEN3 version does not have the oring on the weight.

To eliminate any potential failure points we changed the screw to a roll pin across the plastic end piece and the cap is machined on the rod.

FEATURES:
  • Drop-in replacement for standard buffer and spring
  • Reduce felt recoil
  • Keep the buffer spring from rubbing against the inner wall of the buffer tube
  • Buffer mass is designed to stay under constant tension against the bolt carrier
  • Made in the U.S.A.

SPECIFICATIONS:
Length: 7.18"

Equivalent Weight:
  • C: 3.3 oz.
  • H2: 4.7 oz.

Actual Wight - Complete System (new version with stainless steel weight):
  • C: 6.2 oz.
  • H2: 7.4 oz.

INSTALLATION AND MAINTENANCE:
Before installing the recoil spring, it is always a good idea to retighten the screws using either using two 3/32 hex key and fully tightening both screws at the same time or using one 3/32 hex key and using the hole in the rod for leverage.

The screws should be re-tightened every time maintenance is performed on the firearm.

The polymer bumper goes towards the rear of the firearm and the weight mass with the o-ring goes towards the bolt carrier.

The SRS can be installed with our without the buffer retainer. Most people run the SRS without the buffer retainer for ease of maintenance.