You are here: Home > Rearden Thread Pitch > 1/2x28
Sort By:
Page of 1
Rearden FHD Flash Hider - Nitride - Fits Plan B Mounts Rearden FHD Flash Hider - Heat Treat - Fits Plan B Mounts Rearden Mini Muzzle Device - Nitride - Fits Plan B Mounts
These fit the plan B type mounts. This is an updated version that has larger wrench flats on the rear. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.

Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy. The nitride finish does lead to a tighter seal, with that said, it is extremely important to torque and rockset your muzzle device to the barrel properly.

Specs:
  • 17-4 PH H900
  • Plan B Adapter Overrun approximately 1.05″
  • 1/2-28 Threads (.375 Bore)
  • 5/8-24 Threads (.375 Bore)
  • Black Nitride Finish (67 HRC Surface Hardness)
  • Now with bigger nuts! 13/16″
  • Shims Not Included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
These fit the plan B type mounts. This is an updated version that has larger wrench flats on the rear. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.

Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy.

Specs:
  • 17-4 PH
  • 1/2-28 Threads (.375 Bore)
  • 5/8-24 Threads (.375 Bore)
  • Now with bigger nuts! 13/16″
  • Atlas adapter overrun approximately 1.050″
  • Shims Not Included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.

Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy.

Specs:
  • 17-4 PH H900
  • Q Plan B Compatible
  • Atlas Adapter Overrun approximately 0.05″
  • 1/2-28 Threads 25 Degree Taper Compatible
  • 5/8-24 Threads 25 Degree Taper Compatible
  • Black Nitride Finish (67 HRC Surface Hardness)
  • Now with bigger nuts! 13/16″
  • Shims Not Included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
Rearden Mini Muzzle Device - Heat Treat - Fits Plan B Mounts Rearden SPB Single Port Brake - Nitride - Fits Plan B Mounts Rearden SPB Single Port Brake - Heat Treat - Fits Plan B Mounts
Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.

Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy.

Specs:
  • 17-4 PH H900
  • Q Plan B Compatible
  • Atlas Adapter Overrun approximately 0.050″
  • 1/2-28 Threads 25 Degree Taper Compatible
  • 5/8-24 Threads 25 Degree Taper Compatible
  • H900 Wheat Finish
  • Now with bigger nuts! 13/16″
  • Shims Not Included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
    These fit the plan B type mounts. This is an updated version that has larger wrench flats on the rear. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.

    Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy. The nitride finish does lead to a tighter seal, with that said, it is extremely important to torque and rockset your muzzle device to the barrel properly.

    • Specs:
    • 17-4 PH H900
    • Plan B Compatible
    • Atlas Adapter Overrun approximately 1.05″
    • 1/2-28 Threads .375 Bore
    • 5/8-24 Threads .375 Bore
    • Black Nitride Finish (67 HRC Surface Hardness)
    • Shims Included
    These fit the plan B type mounts. This is an updated version that has larger wrench flats on the rear. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.

    Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy. The nitride finish does lead to a tighter seal, with that said, it is extremely important to torque and rockset your muzzle device to the barrel properly.

    Specs:
    • 17-4 PH
    • Plan B Compatible
    • Atlas Adapter Overrun approximately 1.050″
    • 1/2-28 Threads .375 Bore
    • 5/8-24 Threads .375 Bore
    • H900 Wheat Finish (Variations exist)
    • Shims Included